www.kobd2.jp

Anything about cars
kobd2 by kobd2 @
In automotive components, the most vulnerable could be the bumper. It could possibly only be replaced in case the bumper was pushed out of form, but under regular situations, when the bumper just gently abrasions, even though not hurt, but whole BMW ICOMof scars and very unattractive, it should find a technique to patch superior. In addition, so that you can steer clear of the bumper numerous bruises, generally have some defense solutions ought to be pointed out, the only real method to make the bumper constantly preserve a vibrant deal with.

Suggested the number of the devoted chemical synthesis agent repair bumper is a great way, and also the procedure OBD2 Bluetoothis incredibly simple, anybody is often fixed, whilst it is actually difficult to return to the new overall look, but tend not to seem thoroughly, it really is hard to inform the difference degree. The ways are as follows:

1. Slashing the bumper higher than the キセノンランプ  burr, it is advisable to use a knife to chop off the total finishing sleek, it's simple to maintenance. The potholes parts coated with putty to really make it sleek.

2. Bumper scars normally stick all over plenty of dirt and the the putty adhere firmly, really should be cleaned. The overall impact is rather great by using a brush.

3. Bumper piles of oil, the putty will not be effortless cement, so it is best to patch section of the stripping paint diluent.

4. Put together nearer to your shade of assorted colours of putty, the only option.

5. Hybrid bumper along with the the obd2故障診断 putty gray primary, hardener extrusion same duration, in accordance towards the solution guidance.

kobd2 by kobd2 @
Air inlet or air inlet grille, electronic supporter. Car air inlet or air inlet grille, these elements of the electronicAutel Maxidas ds708fan really should usually check for debris. If there is particles is often blown away with compressed air machine. On top of that, within the condition of engine cooling, can use h2o cannon in the inside out to clean about sections.

Battery. While in the winter season, the vehicle battery electrode wiring at is most certainly obd2 bluetooth to go incorrect. Test the driving force, in the event the electrode wiring within the inexperienced oxide, must use drinking water to clean away the green oxide may cause the generator ability is minimal, the point out in the battery in a very loss of electric power may bring about critical battery scrap, or car defeat the fireplace.

Interior. Because of the summer time heat, rainy, motor vehicle carpet, flooring mats and various nooks breeding floor for numerous micro organism. Using the onset of winter season, the home windows aren't any for a longer time OBD2 ソフト always open up, the air inside of will turn out to be cloudy, uncomfortable scent, odors and micro organism destructive to human overall health hazard, therefore, in the time period, it is vitally needed with the motor vehicle to accomplish a thorough interior sterilization and cleaning.
kobd2 by kobd2 @
X431 may be the regular machines for experts. Diagnostic capabilities compact primary device, highly effective, hassle-free update, common connectors, quick and it has grow to be the main choice for technicians.


X431 Diagun has powferful and complete fuctions. The five primary capabilities as pursuing: Open auto analysis purpose, the update feature mail, PDA purpose, multi-language display purpose and print operate.


X431 Diagun is coverage of most well-known vehicle manufacturers, it supports TOYOTA, LEXUS, NISSAN, HONDA, MITSUBISHI, MAZDA, M.Benz, BMW,VW / AUDI, OBD / EOBD, OPEL, VOLVO, FIAT, RENAULT, HYUNDAI, DAEWOO, GM, FORD, CHRYSLER,Other EU cars and trucks and Asian automobiles.



Launch X431 is totally appropriate with distinctive languages. It supports English, Spanish, Portuguese, Russian etc.
kobd2 by kobd2 @
(1) paint. Winter morning, dew 2012 summer months drinking water much more the vehicle surface area frequently pretty wet, if apparent scratches within the area of the car or truck, it ought to be finished in time paint therapy GM Tech2to stay clear of scratches on elements from moisture and corrosion. In addition, from the period when it is best for your car or truck floor time cleaning, sharpening and waxing, sealing glaze or coating a series of natural beauty routine maintenance.



(2) tire routine maintenance. The tire performs a pivotal job while in the safety of X431vehicles traveling. Specifically in the winter, because of towards the reasonably minimal temperatures, the tire is important to add air force to help keep them within the air force variety, simultaneously, you need to also look at the tire scratches, is not hard to harden inside the winter season due to the fact the rubber extra brittle, tires easy to leak, or perhaps rolling tire OBD2 ソフト.



(3) the motor compartment.Autel To the wintertime, the driving force need to generally verify the engine compartment, engine oil, brake fluid and antifreeze, see oil adequacy, irrespective of whether the deterioration towards the substitution cycle. These fluids like blood of your auto, into the alternative cycle, and must be changed, to be able to guarantee sleek oil circulation.

(4) Heater pipeline Digimaster 3and lover. Reduced winter season temperatures, the vehicle appears white frost phenomenon, in this particular year, pay out particular awareness towards the windshield defroster vent wind is typical, the adequacy on the warmth. When there is a dilemma, to generally be resolved immediately, normally, will provide the driver provide insecurity.
kobd2 by kobd2 @
One, the subsequent conditions arise the necessity for idle air amount discovering ".

"Idle air quantity learning" Maxidas ds708is the engine speed maintained in just a predetermined array, a functionality to regulate the idling intake quantity. This operation needs to be performed from the following situation:

Each time you swap the X431 electronic throttle control actuator, throttle overall body or ECM.

2 idle or the ignition timing is outside the house the specified vary.

Second, the quantity of idle air studying prerequisite

Idle air volume finding out "to Maxidas ds708confirm that all of the next problems. Even momentarily, should you have any of such conditions is not happy, the training operation is going to be canceled.

engine idling, the battery voltage is bigger than twelve.9V.

start out the motor and engine temperature as many as ordinary operating temperature of 70 to one hundred ° C (158 to 212 ° F).

c PNP swap while in the ON point out.

d. shut down the air con, headlights, rear window defogger electrical load.

e. cooling lover motor is just not running.

f steering wheel in the straight-ahead place.

g the auto is stationary.

The h. Preheat transmission. ds708A / T versions, to cars for that usage of CONSULT-Ⅱ diagnostic show right until "A / T" program "DATAMONITOR" (details checking) mode "FLUID TEMP SE" (oil temperature sensor) values ??under 0.9 V. For any / T styles with CONSULT-Ⅱ diagnostic manual transmission products, 10min to cars.



http://kobd2.blogspot.com/
kobd2 by kobd2 @
As all of us know Digimaster 3 is fantastic odometer correction resource, and now it truly is up to date. The detial details as following:

1. DigiMaster-III Newly extra critical programming perform

It can be relevant for high-class automobiles including Mercedes Benz and BMW. Innovative automatic method for essential programming technologies, multi-language operation, the crucial element programming total in one go, effectively make sure the safety of studying and producing facts.

2. DigiMaster-III New Generation Core Framework

Making use of the brand new G3 system of Yanhua Tech as well as the progressive usage manner of "Pay while you go"support the newest motor vehicle, global synchronic up grade, prolong and combine functions freely.

3. Digimaster 3  Clever Procedure Platform

Up grade the single-task technique into intelligent multi-task and multi-thread operation system, prolong features freely and unlimitedly.

4. Improve the single-task technique into clever multi-task and multi-thread procedure technique, prolong functions freely and unlimitedly.

5. DigiMaster-III Comprehensive Upgraded Procedure Interface

It breaks far from the first monotonous static interface, determined by IE main engineering to guidance loaded and dynamic consequences at the same time as state-of-the-art skin interface. And it's more gorgeous and welcoming, supports for lots of language across the entire world.

6. DigiMaster III Higher Definition Electronic Monitor

Update the small definition Liquid crystal display shade display (320X240) to the imported Hd electronic TFT color monitor (800X480) which implementing the precision contact technolog







http://kobd2.blogspot.com/
kobd2 by kobd2 @
Reflect the homeowners: the car unstable idle, no cold vehicle idling and low-speed weakness.

Car for any employed vehicle just then, in accordance with all the demands ELM327of the motive force first cleaning upkeep injector, however the fault has not ruled out. Initially extracts the fault codes, for that blended gasoline focus adjusting lousy ", the multimeter to measure the voltage of your output signal on the oxygen sensor, the pin 10 is measured from your motor command unit, the voltage concerning the 28 feet have 40800mV variations in an effort to more properly measure the oxygen sensor switch the oscilloscope detects oxygen sensor waveform and located not the principles of the waveform, occasionally easy burr. The output sign voltage differs between 24mV and 840mV, the cycle is about 1.5s, the motor speed can also be using this cycle fluctuations. Is just not the idle pace fluctuation prompted by the valve? To unplug idle valve plug found idle pace elevated to 1200r/min, the motor command unit for that idle valve regular control, was noticed using an oscilloscope waveform observed: 1 foot 5V sq. wave, responsibility cycle of sixty two.3% ; 2 ft 5V sq. wave, in addition to a obligation cycle of 39%; 3 toes 1. 5V DC voltage. Noticed failure phenomenon is to some degree very similar towards the Santana 2000 (with the engine distributor) ignition too early, however the vehicle doesn't have a distributor, crankshaft placement sensor, in order that they checked the valve timing identified valve timing when the token is regular, you can find no challenge. Measurement info stream Table 1-10.


Suspected auto a mixed fuel of improperly modified, then disconnect the consumption air stress sensor, the vacuum tube and stuffed utilizing a vacuum gun to provide a vacuum, GM Tech2to the consumption air force sensor can offer a degree of vacuum somewhat decrease when compared to the genuine pressure while in the idling state steady procedure. Is equal into the motor management unit to deliver a pseudo ingestion Ford VCMair pressure sign, to add concentrated gasoline mixture, can be noticed which the improvements while in the motor working stability. Just isn't the intake air strain sensor is damaged? To get a new ingestion force sensor, motor idling or swimming over. The strain sensor is not really harmed, failure, you will find other good reasons.



Detected consumption pressure some exception, where by From this inspection to progress along with the subsequent step, the timing belt taken off, the valve timing to adjust to your early route, Digimaster 3not only ineffective, idle fluctuation selection go all the way down to the late route to regulate the two tooth, but also the first condition. Camshaft gear is altered back for the first situation.</p>



<p>Remove the valve chamber address, the look at valve clearance due to this fact, 1, obd2 bluetooth4-cylinder valve gap is too modest, the re-adjusted in accordance with all the information mm, the exhaust valves of the ingestion valve. 0 twenty five 0 3 mm, in the event the idling pace stabilization, troubleshooting.



http://kobd2.blogspot.com/
kobd2 by kobd2 @
Set around the Honda Accord 2.4 L and 3.0 L car or truck dashboard maintenance lights when the odometer mileage OBD2 ソフト of 9 600 km-12 000 km via the ignition swap, servicing lights 2s, while over 12 000 km once the operator has but to get performed servicing routine maintenance Lantern has been shining, timely upkeep to prompt the owners. Once the sedan in servicing requirements odometer zeroing operation, precise solutions are as follows: Convert the ignition swap, urgent the reset button over the instrument panel, right until the odometer demonstrates as "0" thus far. To remind house owners of the prior to in motor vehicle servicing. Consider zero operating unavailable thanks to upkeep lights lit, obd2 software so odometer the cumulative mileage will no more accurate and routine maintenance lights is getting rid of its function.


Honda Accord 2.0 L sedan isn't set about the dashboard maintenance lights "MAIN TENANCE REQUIRED" indicator on the dashboard obd2 connector prompts, in the event the mileage of near to twelve 000 km. The indicator light changes from eco-friendly to yellow, a lot more than twelve 000 km routine maintenance has still being executed, the indicator from yellow to red. Upkeep after. So as to be certain that the guidelines in the indicator perform, zeroing procedure, the precise process of procedure is as follows.


(1) Disconnect obd2 scan tool the ignition switch, the ignition crucial to the tachometer down below the tank;

(2) the steering column beneath the instrument panel within the suitable aspect of your button is pressed and preserved for 3 s;

(3) keep down the mixture of your car diagnostic tool instrument the correct facet in the "SELECT" and "RESET" button, change the ignition change, release the button inside the 10s just after zeroing procedure is complete.


kobd2 by kobd2 @
Fox C307 LVSFCFME96F025904 point out vehicle mileage 620KM new car opened more than 1 week, motor failure warning mild in motion, the homeowners explain GM Tech2fault lights, instrument information and facts middle did not prompt.

Check stint sleek engine idle, acceleration, there's no apparent fault. WDS detecting an engine there is certainly a fault, PCM P1701, its meaning is the row of the cylinder fuel injection amount is also dilute. Before this, you will find quite a few much more cars are due to the identical fault replaced the gas ELM327 injectors and gasoline rail just after typical. Substitute from the gasoline rail and injectors, cleaning the throttle KAM reset soon after the check failure, then cross the auto.

Owners after once more arrived to the station the following day, and repair the engine warning lights. Self Test P1701 with a failure, information study data logger, Ford VCMlong-term gasoline correction value eleven.29%, short-term gas correction worth of 2.9%. Entrance oxygen sensor information, 8 instances within 10 seconds of switching voltage in the 0.1V to 0.8V consistently beating. Engine drinking water temperature of 93 levels, the intake air pressure sensor information is read. All of the above data also do not see exactly where the issue lies.

Connect the fuel stress gauge idling stress 3.0bar, challenging acceleration, gasoline pressure between 2.8bar-3.0bar beating. Determining the lower pressure gasoline pump, replace the gasoline pump troubleshooting .



Evaluation; checking the sole components from the mixed gasoline will be the oxygen sensor, if there's no fault inside the oxygen obd2 bluetoothsensor alone, there could be considered a fuel injector mechanical failure, or the misalignment on the sensor sign enter PCM, the gasoline stress is minimal. Maintenance widespread to many staff that are impervious to grasp because of the operating principle and troubleshooting usually making use of the substitution system to diagnose. I believe that the substitution method to diagnose faults naturally is rapidly, and may conserve a whole lot of upkeep hyperlink, but in the situation of equipment insufficiency or go out to repair the substitution system to diagnose faults blindness is pretty crystal clear. From simple to complex, from outside to inside, itemized upkeep, fault diagnosis method demanding Digimaster 3scientific qualities essential for each of our professionals.



http://kobd2.blogspot.com/
kobd2 by kobd2 @
Buick LaCrosse substitute ELM327 cylinder head, camshaft timing chain to re-proofing. Camshaft timing chain proofreading the Notes under.

(1) timing chain over the 3 colored one-way links, together with two pink, someone blue consumption camshaft actuators mounted on the camshaft, the blue link the timing on the intake camshaft adjuster mark alignment.

(2) with the openings of GM Tech2 the cylinder head down to the timing chain, making sure that the chain bypassed on both sides from the cylinder system bosses.

(3) in the crankshaft sprocket mounted to the crankshaft, the timing chain wound across the crankshaft sprocket plus the timing marks over the crankshaft sprocket are aligned using the timing chain clockwise direction a pink chain, aligned pink website link around like clock fingers 5 o'clock position.

(4) the exhaust camshaft adjuster mounted into the camshaft, the portion of chain in the very last just one pink plus the exhaust camshaft adjustment over the timing marks are aligned.

(5) Verify the many coloured url with X431 Diagun the timing marks aligned.

(6) to adjust the timing chain tensioner back again compressed condition right after set up, mounted it cause tensioner tensioner timing chain.

(7) pulled the crank, equipment observation crankshaft rotation approach for catching, if any, catching, you would like to re-check the timing.

Note: The inlet and exhaust camshafts are

Autel not interchangeable, and might not be mounted completely wrong, to the left in Figure 2 to the exhaust camshaft, the proper side with the ingestion camshaft.





http://blog.goo.ne.jp/kobd2
New Post
feeds Feeds
kobd2 automycar ansmokeshop deborahiii
colsyre Mary20 coujan Pat24
Jenn19 Jennifer21 Yvonne19 Victoria27